Open Access Te Herenga Waka-Victoria University of Wellington
Browse

Disparity Between Reality and Theoretical Models - Predicting Moisture and Mould Growth in New Zealand Houses

Download (6.43 MB)
thesis
posted on 2021-07-18, 22:18 authored by Buet, Sarah

A common goal amongst building practitioners is to create warmer, healthier, and drier houses. A key barrier to this is the presence of excessive moisture, the leading cause of mould growth within buildings. New Zealand Building Code Clause E3 ‘Internal Moisture’ has been set out to control internal moisture within a house, however, there is currently no prescribed method which practitioners can use to demonstrate compliance. Tools such as ASHRAE Standard 160 ‘Criteria for Moisture Control Design Analysis in Buildings’ can be used to predict internal conditions; however, studies have shown that such tools rely upon a range of possibly inappropriate assumptions and may not give accurate results. When looking specifically at ASHRAE Standard 160, the Indoor Design Temperature and Indoor Design Humidity application requires assumptions such as the presence of heating systems, a minimum heating setpoint, ventilation rates, and moisture generation rates of occupants. This research aimed to understand whether, considering the assumptions it makes, can ASHRAE Standard 160 be used in New Zealand to predict mould growth? It went on further to understand how the results produced by ASHRAE Standard 160 aligned with measured data?

Using the yearlong records of New Zealand houses' external conditions (temperature and relative humidity) collected from the 2015 Pilot Housing Survey, two ‘Design Parameters’, the Indoor Design Temperature and Indoor Design Humidity (Simplified and Intermediate Method), were applied from ASHRAE Standard 160. These two ‘Design Parameters’ were the only two parameters assessed due to the limitations of the data that was able to be used from the Pilot Housing Survey. Other ‘Design Parameters’ in ASHRAE Standard 160 include exposure conditions and material properties, as well as a Full Parameter Calculation of Indoor Design Humidity, however, there was insufficient information from the 2015 Pilot Housing Survey to compare these parameters to. Having applied the Indoor Design Temperature and Indoor Design Humidity formula, year-long records of the same houses' internal conditions (temperature and relative humidity) were then used to identify discrepancies between the measured data and the theoretical conditions developed by ASHRAE Standard 160.

To understand how discrepancies may be occurring, it was important first to understand the assumptions that ASHRAE Standard 160 is making when applying the Indoor Design Temperature and Indoor Design Humidity formula. The five most critical assumptions that these two ‘Design Parameter’ were implementing were:• A minimum heating setpoint of 21.1°C would be applied whenever the running 24- hour average outdoor temperature dropped below 18.3°C.

• Under the Simplified Indoor Design Humidity, the indoor relative humidity was closely dependent on the running 24-hour average outdoor temperature.

• The number of occupants in a house was dependant on the number of bedrooms within the house.

• Each occupant generates approximately 3L per day.

• The buildings' infiltration is either 0.2 ACH for a standard construction or 0.1 ACH foran airtight construction.

Having compared and analysed the measured indoor conditions and the conditions outlined by ASHRAE Standard 160, a number of discrepancies became evident. This in turn suggested that the above assumptions that ASHRAE Standard 160 made in order to apply Indoor Design Temperature and Indoor Design Humidity (Simplified and Intermediate Method) are not reflective of New Zealand. The key conclusions from this research were:• The minimum heating setpoint of 21.1°C is not applicable in New Zealand houses.

Instead, the application of the To24h + 2.8°C formula across all outdoor temperatures was favourable. Alternatively, further research could suggest a more applicable minimum heating setpoint for New Zealand.

• Overall the Simplified Indoor Design Humidity is a more suitable method of determining the Indoor Design Humidity than the Intermediate Indoor Design HumidityIt was found that overall, the Simplified Indoor Design Humidity matched the measured indoor relative humidity better than the Intermediate Indoor Design Humidity. This was concluded to be due to the fact that the assumptions in the Intermediate Indoor Design Humidity did not reflect the reality of New Zealand houses. However, there is the possibility for the Intermediate Indoor Design Humidity to be altered to reflect the reality of New Zealand houses better.

• The Intermediate Indoor Design Humidity parameters are altered to reflect the reality of New Zealand houses better.

This research identified that the two main parameters, Design Moisture Generation and Design Ventilation Rate, do not reflect how New Zealanders occupy their houses. By undertaking further research into refining these parameters, the application of the Intermediate Indoor Design Humidity may become more suitable for New Zealand.

Having identified discrepancies and the reasons for these discrepancies, this research began to investigate areas in which further research could improve the suitability of ASHRAE Standard 160 in New Zealand. This included additional information such as occupant moisture generation rates and any significant renovations on the houses, being gathered in future Pilot Housing Surveys. Further analysis could be undertaken on inputs such as the Moisture generation Rate and the Design Ventilation Rate by gathering this additional information. This in turn would allow for the alternative inputs to be analysed to understand how these ‘Design Parameters’ could be altered to reflect the reality of New Zealand houses better.

History

Copyright Date

2021-07-14

Date of Award

2021-07-14

Publisher

Te Herenga Waka—Victoria University of Wellington

Rights License

Author Retains Copyright

Degree Discipline

Building Science

Degree Grantor

Te Herenga Waka—Victoria University of Wellington

Degree Level

Masters

Degree Name

Master of Architectural Science (Research)

ANZSRC Type Of Activity code

1 PURE BASIC RESEARCH

Victoria University of Wellington Item Type

Awarded Research Masters Thesis

Language

en_NZ

Victoria University of Wellington School

Wellington School of Architecture

Advisors

Isaacs, Nigel